YAESU - CT-62 - CAT INTERFACE CABLE - TO CONNECT A PERSONAL COMPUTER TO COMPATIBLE YAESU TRANSCEIVERS

NOTE:
It uses the 9-pin RS-232 serial port.
It can also be used on a USB port with the optional Atlantis SERIAL / USB adapter available among the accessories listed below.

FT-METER - LDG - Meter for Yaesu FT-857/897

Yaesu's popular FT-857(D) and FT-897(D) transceivers are wonders of compact efficiency. These do-anything, go-anywhere transceivers were science fiction just a few years ago, but ham's today are using them in shacks, mobiles and on dxpeditions from the back yard to the top of the world. 

About the only problem with these radios is that us hams who are old enough to remember when stuff like this really was science fiction are also old enough to wish that the display was just little bit bigger. As we grow in wisdom and experience, we also grow to depend on bifocals; those tiny little screens are just plain hard to read! Add to that a strong desire to see a real live meter needle bouncing on voice peaks, and you find yourself wishing Yaesu had thought all this through when they designed the radio. 

Well, in fact they did. A little known feature of these radios, noticed only by compulsive manual readers, is a meter jack on the bottom of the front panel. You have to figure that Yaesu knew they needed a bigger display all along, but just left it as an exercise for the user. Well, help is here! The LDG FT-Meter is a low-cost, plug-and-play solution to all your FT metering needs. 

The FT-Meter presents a lush, highly readable 2.5" meter face with calibrated scales for signal strength and discriminator reading on receive, and power output, SWR, modulation, ALC action and supply voltage on transmit. Each function is selectable from the radio's menu. Easily visible from anywhere on your desk or dash, the FT-Meter is illuminated by any external 12 vdc source. The FT-Meter comes fully assembled and ready to go; just plug it into the radio and you're in the picture like never before. Order yours today.

• Receive: S-Meter, Discriminator or Voltage
• Transmit: RF Power, SWR, Modulation, ALC or Voltage
• Cable length 3 feet
• Sensitive 500 uA meter movement
• Externally powered cool blue backlighting
• On/Off switch for backlight.
• Backlighting requires 11 to 15 volts, 100 mA
• Size: 3.6W x 3.0 D x 2.6H inches
• Weight: 0.5 lb.
• For use with FT-857(D) and FT-897(D) only.

YAESU - YF-122S - SSB COLLINS MECHANICAL FILTER 2.3 kHz - Suitable for use on Yaesu transceivers FT-817 / FT-818ND / FT-857 / FT-897

YAESU - YF-122CN - Collins Mechanical CW Filter - 300 Hz - Suitable for use on Yaesu FT-817 / FT-818ND / FT-857 / FT-897 Transceivers

YAESU - YSK-857 - Separation Kit for FT-857D - Complete with front panel mounting hardware and two 19.6 foot (6 m) interconnecting cables.

The YSK-857 Separation Kit consists of Front Panel mounting hardware and two 19.6 foot (6 m) interconnecting cables for the Front Panel. The kit allows the main body of the FT-857/D to be installed in the trunk, or anywhere else out of the way. The kit consists of:

 Front Panel Nest
 Controller Extension Cable
 Speaker Extension Cable
 Microphone Extension Cable
 Double-Sided Adhesive Tape
 Mounting Screws, Washers & Nuts

KENWOOD - PG-5A - Data connector cable (mobiles) - To be used between a PC and the radio to operate Packet - PC serial connector user provided 

KENWOOD - DFK-3D - Remote Mounting Kit For Front Panel (3 M cable) - QUICK AND EASY ASSEMPLY / DISASSEMBLY

KENWOOD - PG-5F - FRONT PANEL EXTENSION KIT - 4 m. long - for Kenwood transceivers TM-V71e, TM-D710E, TM-D710GE

KENWOOD - HS-5 - PROFESSIONAL DE-LUXE COMMUNICATION HEADPHONES - Specific to hear better vocal frequencies in the noise 

STANDARD VERSION: MONO
HSP MODIFIED VERSION: STEREO

The standard version offered by Kenwood is generally usable on every radio device, as amateur radio transmissions are MONO.
However, there are cases in which, with some radios that provide it, it is possible to hear the sound of VFO A on one ear and the VFO B on the other, to monitor 2 frequencies simultaneously but separately.
In this case we have planned a modification of this headset, which we operate in our laboratory, and which consists of rewiring the internal pavilions so that they are separated and doing the same with the connector, replacing it with a STEREO.
The user can then choose, when purchasing the product, the one that suits him/her best.

- 2 different types of interchangeable ear cups supplied.
- 6,3 mm jack connector

TECHNICAL SPECIFICATIONS:

KENWOOD - HS-6 - LIGHT COMMUNCATIONS HEADPHONES
Specifically designed for use in radio-telecommunication systems

NO LONGER MANUFACTURED - NO MORE AVAILABLE