M2 - 2M 4PT PD - 2 METERS 4 PORT POWER DIVIDER - FREQUENCY: 144-148 MHz -  Aluminum Coaxial - 3 kW - 50 ohm -  N female connectors

M2 Antennas Power Dividers are non-isolation type dividers that serve as RF combiners and splitters for 50 ohm antennas and feedlines. They are carefully hand-crafted to achieve their design frequency range.

M2 Antennas Power Dividers are made with Type N female connectors so they have extremely low loss and constant impedance characteristics. Power Dividers are used in VHF, UHF and SHF arrays to impedance match two or four Loop or Yagi antennas that are fed in phase, separated by the proper stacking spacing, and pointed in the same direction. As compared to a single antenna, this technique can yield 3 dB gain for two antennas and nearly 6 dB gain for four antennas, less only the minor losses of the phasing lines and the power divider. Each pair of stacked antennas nearly doubles the effective radiated power of the station. 

M2 Antennas Power Dividers for 144 MHz, 430 MHz and 1.2 GHz are constructed with aluminum tubing or aluminum blocks and solid metal center conductors to make coaxial lines with air dielectric, so their losses are nearly immeasurable. These two-port and four-port Power Dividers feature aluminum brazed joints, machined end blocks and 'O' ring sealed coaxial connectors of the highest quality. Each M2 Antennas Power Dividers has less than 0.1 dB loss and handles 3 kW of RF power. Two-port dividers are used for a pair of Horizontal Omni Loops or a pair of Yagi antennas with equal length of 50 ohm low loss coaxial cables with Type N connectors. Two-port power dividers are also used in arrays of eight Yagis or multiples, to combine each pair of four antennas that are served by four-port Power Dividers. 

ECO - ART. 165 - 2 PORT POWER DIVIDER - OPERATING FREQUENCY: 144-148 MHz - POWER: 1000 W - IMPEDANCE: 52 OHM

ECO - ART. 166 - 4 PORT POWER DIVIDER - OPERATING FREQUENCY: 144-148 MHz - POWER: 1000 W - IMPEDANCE: 52 OHM

ECO - ART. 46 - 4 PORT POWER DIVIDER - OPERATING FREQUENCY: 88-97 MHz - POWER: 1000 W - IMPEDANCE: 52 OHM

ECO - ART. 47 - 4 PORT POWER DIVIDER - OPERATING FREQUENCY: 98-108 MHz - POWER: 1000 W - IMPEDANCE: 52 OHM

ECO - ART. 167 - 4 PORT POWER DIVIDER - OPERATING FREQUENCY: 420-450 MHz - POWER: 1000 W - IMPEDANCE: 52 OHM

ECO - ART. 168 - 4 PORT POWER DIVIDER - OPERATING FREQUENCY: 420-450 MHz - POWER: 1000 W - IMPEDANCE: 52 OHM

KLM - 2M-2N - 2 METERS 2 PORT POWER DIVIDER - FREQUENCY: 144-148 MHz - 2 kW p.e.p. - 50 ohm -  N female connectors

Broadband power divider/couplers are available for use in stacking VHF/UHF beams.

These units replace the quarter-wave matching cable sections, barrel connectors, and "T" connectors that are ordinarily used. Matching input and output to 50 ohm impedances is automatic.
Use of these low loss devices results in significant savings in cost and complexity, and substantial reduction in cable and connector losses.
Construction is of copper tubing assuring minimal loss and providing excellent physical rigidity. The units are supplied
with type "N" input and output connectors only.
Power rating is conservatively 2 kW peak envelope power.
They are "natural" for any array from two to thirty-two antennas.

KLM - 440-4N - 70 CM. 4 PORT POWER DIVIDER - FREQUENCY: 420-450 MHz - 2 kW p.e.p. - 50 ohm -  N female connectors

Broadband power divider/couplers are available for use in stacking VHF/UHF beams. 
These units replace the quarter-wave matching cable sections, barrel connectors, and "T" connectors that are ordinarily used. Matching input and output to 50 ohm impedances is automatic.
Use of these low loss devices results in significant savings in cost and complexity, and substantial reduction in cable and connector losses.
Construction is of copper tubing assuring minimal loss and providing excellent physical rigidity. The units are supplied
with type "N" input and output connectors only. 
Power rating is conservatively 2 kW peak envelope power. 
They are "natural" for any array from two to thirty-two antennas.

KLM - 440-2N - 70 CM. 2 PORT POWER DIVIDER - FREQUENCY: 420-450 MHz - 2 kW p.e.p. - 50 ohm -  N female connectors

Broadband power divider/couplers are available for use in stacking VHF/UHF beams. 
These units replace the quarter-wave matching cable sections, barrel connectors, and "T" connectors that are ordinarily used. Matching input and output to 50 ohm impedances is automatic.
Use of these low loss devices results in significant savings in cost and complexity, and substantial reduction in cable and connector losses.
Construction is of copper tubing assuring minimal loss and providing excellent physical rigidity. The units are supplied
with type "N" input and output connectors only. 
Power rating is conservatively 2 kW peak envelope power. 
They are "natural" for any array from two to thirty-two antennas.