CUSHCRAFT - A535SK - STACKING KIT FOR 2  BEAMS FOR 6 METERS (50 MHz), IDEAL FOR CUSHCRAFT A50-3S OR A50-5S

CUSHCRAFT - PD-4 - 4 PORT POWER DIVIDER FOR THE 2 METERS BAND- 144 MHz - USE IT WITH 4 EQUAL ANTENNAS

Made up of coaxial cable, the PD-4 is therefore very flexible, unlike rigid power dividers.

Just add 4 equal lengths of the same coaxial cable to the 4 outputs to make a perfect coupling of 4 equal antennas operating at 144 MHz.

M2 - 23 CM 2 PORT POWER DIVIDER - 1240-1300 MHz -  Aluminum Coaxial - 3 kW - 50 ohm -  N female connectors

M2 Antennas Power Dividers are non-isolation type dividers that serve as RF combiners and splitters for 50 ohm antennas and feedlines. They are carefully hand-crafted to achieve their design frequency range.

M2 Antennas Power Dividers are made with Type N female connectors so they have extremely low loss and constant impedance characteristics. Power Dividers are used in VHF, UHF and SHF arrays to impedance match two or four Loop or Yagi antennas that are fed in phase, separated by the proper stacking spacing, and pointed in the same direction. As compared to a single antenna, this technique can yield 3 dB gain for two antennas and nearly 6 dB gain for four antennas, less only the minor losses of the phasing lines and the power divider. Each pair of stacked antennas nearly doubles the effective radiated power of the station. 

M2 Antennas Power Dividers for 144 MHz, 430 MHz and 1.2 GHz are constructed with aluminum tubing or aluminum blocks and solid metal center conductors to make coaxial lines with air dielectric, so their losses are nearly immeasurable. These two-port and four-port Power Dividers feature aluminum brazed joints, machined end blocks and 'O' ring sealed coaxial connectors of the highest quality. Each M2 Antennas Power Dividers has less than 0.1 dB loss and handles 3 kW of RF power. Two-port dividers are used for a pair of Horizontal Omni Loops or a pair of Yagi antennas with equal length of 50 ohm low loss coaxial cables with Type N connectors. Two-port power dividers are also used in arrays of eight Yagis or multiples, to combine each pair of four antennas that are served by four-port Power Dividers. 

NOTE:
IMAGES ARE FOR EXAMPLE.
PRODUCTS CAN AESTETICHALLY VARY DEPENDING ON PRODUCTION LOTS.

TONNA - 29223 - 2 PORT 23 CM. POWER DIVIDER - FREQUENCY RANGE: 1250-1300 MHz - CONNECTORS: N female

TONNA - 29423 - 4 PORT 23 CM. POWER DIVIDER - FREQUENCY RANGE: 1250-1300 MHz - CONNECTORS: N female

M2 - 2M 4PRT PD - 4 PORT 23 CM. POWER DIVIDER - FREQUENCY RANGE: 1240-1300 MHz - CONNECTORS: N female

M2 Antennas Power Dividers are non-isolation type dividers that serve as RF combiners and splitters for 50 ohm antennas and feedlines. They are carefully hand-crafted to achieve their design frequency range.

M2 Antennas Power Dividers are made with Type N female connectors so they have extremely low loss and constant impedance characteristics. Power Dividers are used in VHF, UHF and SHF arrays to impedance match two or four Loop or Yagi antennas that are fed in phase, separated by the proper stacking spacing, and pointed in the same direction. As compared to a single antenna, this technique can yield 3 dB gain for two antennas and nearly 6 dB gain for four antennas, less only the minor losses of the phasing lines and the power divider. Each pair of stacked antennas nearly doubles the effective radiated power of the station. 

M2 Antennas Power Dividers for 144 MHz, 430 MHz and 1.2 GHz are constructed with aluminum tubing or aluminum blocks and solid metal center conductors to make coaxial lines with air dielectric, so their losses are nearly immeasurable. These two-port and four-port Power Dividers feature aluminum brazed joints, machined end blocks and 'O' ring sealed coaxial connectors of the highest quality. Each M2 Antennas Power Dividers has less than 0.1 dB loss and handles 3 kW of RF power. Two-port dividers are used for a pair of Horizontal Omni Loops or a pair of Yagi antennas with equal length of 50 ohm low loss coaxial cables with Type N connectors. Two-port power dividers are also used in arrays of eight Yagis or multiples, to combine each pair of four antennas that are served by four-port Power Dividers. 

NOTE:
IMAGES ARE FOR EXAMPLE.
PRODUCTS CAN AESTETICHALLY VARY DEPENDING ON PRODUCTION LOTS.

M2 - 70CM 4PT PD - 70 CM. 4 PORT POWER DIVIDER - FREQUENCY: 420-450 MHz -  Aluminum Coaxial - 3 kW - 50 ohm -  N female connectors

M2 Antennas Power Dividers are non-isolation type dividers that serve as RF combiners and splitters for 50 ohm antennas and feedlines. They are carefully hand-crafted to achieve their design frequency range.

M2 Antennas Power Dividers are made with Type N female connectors so they have extremely low loss and constant impedance characteristics. Power Dividers are used in VHF, UHF and SHF arrays to impedance match two or four Loop or Yagi antennas that are fed in phase, separated by the proper stacking spacing, and pointed in the same direction. As compared to a single antenna, this technique can yield 3 dB gain for two antennas and nearly 6 dB gain for four antennas, less only the minor losses of the phasing lines and the power divider. Each pair of stacked antennas nearly doubles the effective radiated power of the station. 

M2 Antennas Power Dividers for 144 MHz, 430 MHz and 1.2 GHz are constructed with aluminum tubing or aluminum blocks and solid metal center conductors to make coaxial lines with air dielectric, so their losses are nearly immeasurable. These two-port and four-port Power Dividers feature aluminum brazed joints, machined end blocks and 'O' ring sealed coaxial connectors of the highest quality. Each M2 Antennas Power Dividers has less than 0.1 dB loss and handles 3 kW of RF power. Two-port dividers are used for a pair of Horizontal Omni Loops or a pair of Yagi antennas with equal length of 50 ohm low loss coaxial cables with Type N connectors. Two-port power dividers are also used in arrays of eight Yagis or multiples, to combine each pair of four antennas that are served by four-port Power Dividers. 

NOTE:
IMAGES ARE FOR EXAMPLE.
PRODUCTS CAN AESTETICHALLY VARY DEPENDING ON PRODUCTION LOTS.

M2 - 70CM 2PT PD - 70 CM. 2 PORT POWER DIVIDER - FREQUENCY: 420-450 MHz -  Aluminum Coaxial - 3 kW - 50 ohm -  N female connectors

M2 Antennas Power Dividers are non-isolation type dividers that serve as RF combiners and splitters for 50 ohm antennas and feedlines. They are carefully hand-crafted to achieve their design frequency range.

M2 Antennas Power Dividers are made with Type N female connectors so they have extremely low loss and constant impedance characteristics. Power Dividers are used in VHF, UHF and SHF arrays to impedance match two or four Loop or Yagi antennas that are fed in phase, separated by the proper stacking spacing, and pointed in the same direction. As compared to a single antenna, this technique can yield 3 dB gain for two antennas and nearly 6 dB gain for four antennas, less only the minor losses of the phasing lines and the power divider. Each pair of stacked antennas nearly doubles the effective radiated power of the station. 

M2 Antennas Power Dividers for 144 MHz, 430 MHz and 1.2 GHz are constructed with aluminum tubing or aluminum blocks and solid metal center conductors to make coaxial lines with air dielectric, so their losses are nearly immeasurable. These two-port and four-port Power Dividers feature aluminum brazed joints, machined end blocks and 'O' ring sealed coaxial connectors of the highest quality. Each M2 Antennas Power Dividers has less than 0.1 dB loss and handles 3 kW of RF power. Two-port dividers are used for a pair of Horizontal Omni Loops or a pair of Yagi antennas with equal length of 50 ohm low loss coaxial cables with Type N connectors. Two-port power dividers are also used in arrays of eight Yagis or multiples, to combine each pair of four antennas that are served by four-port Power Dividers. 

NOTE:
IMAGES ARE FOR EXAMPLE.
PRODUCTS CAN AESTETICHALLY VARY DEPENDING ON PRODUCTION LOTS.

M2 - 2M 2PT PD - 2 METERS 2 PORT POWER DIVIDER - FREQUENCY: 144-148 MHz -  Aluminum Coaxial - 3 kW - 50 ohm -  N female connectors

M2 Antennas Power Dividers are non-isolation type dividers that serve as RF combiners and splitters for 50 ohm antennas and feedlines. They are carefully hand-crafted to achieve their design frequency range.

M2 Antennas Power Dividers are made with Type N female connectors so they have extremely low loss and constant impedance characteristics. Power Dividers are used in VHF, UHF and SHF arrays to impedance match two or four Loop or Yagi antennas that are fed in phase, separated by the proper stacking spacing, and pointed in the same direction. As compared to a single antenna, this technique can yield 3 dB gain for two antennas and nearly 6 dB gain for four antennas, less only the minor losses of the phasing lines and the power divider. Each pair of stacked antennas nearly doubles the effective radiated power of the station. 

M2 Antennas Power Dividers for 144 MHz, 430 MHz and 1.2 GHz are constructed with aluminum tubing or aluminum blocks and solid metal center conductors to make coaxial lines with air dielectric, so their losses are nearly immeasurable. These two-port and four-port Power Dividers feature aluminum brazed joints, machined end blocks and 'O' ring sealed coaxial connectors of the highest quality. Each M2 Antennas Power Dividers has less than 0.1 dB loss and handles 3 kW of RF power. Two-port dividers are used for a pair of Horizontal Omni Loops or a pair of Yagi antennas with equal length of 50 ohm low loss coaxial cables with Type N connectors. Two-port power dividers are also used in arrays of eight Yagis or multiples, to combine each pair of four antennas that are served by four-port Power Dividers. 

NOTE:
IMAGES ARE FOR EXAMPLE.
PRODUCTS CAN AESTETICHALLY VARY DEPENDING ON PRODUCTION LOTS.

M2 - 2M 2PT PD HW- 2 METERS HALF WAVE 2 PORT POWER DIVIDER - FREQUENCY: 144-148 MHz -  Aluminum Coaxial - 3 kW - 50 ohm -  N female connectors

M2 Antennas Power Dividers are non-isolation type dividers that serve as RF combiners and splitters for 50 ohm antennas and feedlines. They are carefully hand-crafted to achieve their design frequency range.

M2 Antennas Power Dividers are made with Type N female connectors so they have extremely low loss and constant impedance characteristics. Power Dividers are used in VHF, UHF and SHF arrays to impedance match two or four Loop or Yagi antennas that are fed in phase, separated by the proper stacking spacing, and pointed in the same direction. As compared to a single antenna, this technique can yield 3 dB gain for two antennas and nearly 6 dB gain for four antennas, less only the minor losses of the phasing lines and the power divider. Each pair of stacked antennas nearly doubles the effective radiated power of the station. 

M2 Antennas Power Dividers for 144 MHz, 430 MHz and 1.2 GHz are constructed with aluminum tubing or aluminum blocks and solid metal center conductors to make coaxial lines with air dielectric, so their losses are nearly immeasurable. These two-port and four-port Power Dividers feature aluminum brazed joints, machined end blocks and 'O' ring sealed coaxial connectors of the highest quality. Each M2 Antennas Power Dividers has less than 0.1 dB loss and handles 3 kW of RF power. Two-port dividers are used for a pair of Horizontal Omni Loops or a pair of Yagi antennas with equal length of 50 ohm low loss coaxial cables with Type N connectors. Two-port power dividers are also used in arrays of eight Yagis or multiples, to combine each pair of four antennas that are served by four-port Power Dividers.